Produkten har lagts i din varukorg Visa varukorgenTill kassan
0 Produkter
Varukorg
Din webbläsare stöds ej. För bästa upplevelsen rekommenderas en nyare version eller en annan webbläsare.

Splitters/Förgreningskablar

Förgreningskablar tillåter dig att distribuera ljud till flera platser utan att försämra ljudets kvalitet eller stöta på brum från liknande oljud.
Radial Catapult Mini TX
R800 8028 00
Radial Catapult Mini 4-Channel Cat 5 Audio Snake Transmitter
The Catapult Mini is a 4-channel compact audio snake that allows you to send analog audio signals over standard Cat 5 or Cat 6 shielded twisted pair cable.
  • Send four channels of analog audio over a single Cat 5/6 cable
  • Works with a building’s existing cable infrastructure
  • Compact and lightweight, yet durable and rugged
  • Economical Cat 5/6 cable replaces bulky multichannel audio snakes
Analog audio over Cat 5 wiring
The Catapult Mini RX and TX act like a typical four-channel analog audio snake; they allow you to send mic or line-level signals from one location to another without signal loss, noise, or interference, and without any digital audio conversion needed. What makes the Catapult system unique is that it utilizes Cat 5 Ethernet cable, which is widely available, lightweight, and economical. Simply connect a shielded Cat 5 cable between any two Catapult modules and they will use the analog conductors in the cable to deliver four balanced audio lines to any destination.
Straight-wire passive operation
Catapult modules require no power to operate, and since they keep the signal in the analog realm, no digital conversion is necessary. Straight-wire connection from the XLRs to the RJ45 connector on a Cat 5 cable ensures that your audio passes through without coloration or distortion.
Utilize pre-existing cable installations
As many buildings are already pre-wired for Cat 5, you can take advantage of this to transmit audio between distant rooms without the need to install or supply new cabling. This eliminates the need for bulky and expensive multi-channel audio cable, and allows contractors to benefit from installed network cable and easily connect from one room to another.
Mix & Match
All of the Radial Catapult modules are compatible with each other, and each is sold individually, so you can select whichever combination best suits your needs. The Catapult Mini RX and TX can be used together as a pair, creating a compact 4-channel audio snake. However, if you prefer to have a stage box to plug microphones into, but want a compact breakout cable that fits in the case with the mixer, combine the Catapult TX4 with the Catapult Mini RX. A variety of modules allow you to customize your transmit and receive devices to complement any application.
Radial Catapult Mini RX
R800 8029 00
Radial Catapult Mini 4-Channel Cat 5 Audio Snake Receiver
The Catapult Mini is a 4-channel compact audio snake that allows you to send analog audio signals over standard Cat 5 or Cat 6 shielded twisted pair cable.
  • Send four channels of analog audio over a single Cat 5/6 cable
  • Works with a building’s existing cable infrastructure
  • Compact and lightweight, yet durable and rugged
  • Economical Cat 5/6 cable replaces bulky multichannel audio snakes
Analog audio over Cat 5 wiring
The Catapult Mini RX and TX act like a typical four-channel analog audio snake; they allow you to send mic or line-level signals from one location to another without signal loss, noise, or interference, and without any digital audio conversion needed. What makes the Catapult system unique is that it utilizes Cat 5 Ethernet cable, which is widely available, lightweight, and economical. Simply connect a shielded Cat 5 cable between any two Catapult modules and they will use the analog conductors in the cable to deliver four balanced audio lines to any destination.
Straight-wire passive operation
Catapult modules require no power to operate, and since they keep the signal in the analog realm, no digital conversion is necessary. Straight-wire connection from the XLRs to the RJ45 connector on a Cat 5 cable ensures that your audio passes through without coloration or distortion.
Utilize pre-existing cable installations
As many buildings are already pre-wired for Cat 5, you can take advantage of this to transmit audio between distant rooms without the need to install or supply new cabling. This eliminates the need for bulky and expensive multi-channel audio cable, and allows contractors to benefit from installed network cable and easily connect from one room to another.
Mix & Match
All of the Radial Catapult modules are compatible with each other, and each is sold individually, so you can select whichever combination best suits your needs. The Catapult Mini RX and TX can be used together as a pair, creating a compact 4-channel audio snake. However, if you prefer to have a stage box to plug microphones into, but want a compact breakout cable that fits in the case with the mixer, combine the Catapult TX4 with the Catapult Mini RX. A variety of modules allow you to customize your transmit and receive devices to complement any application.
Radial Catapult TX4
R800 8022 00
Radial Catapult 4-Channel Cat 5 Audio Snake Transmitter
The Radial Catapult™ is a 4-channel modular audio snake that allows you to send analog audio signals over standard Cat 5 or Cat 6 shielded twisted pair cable.
  • Send four channels of analog audio over a single Cat 5/6 cable
  • Works with a building’s existing cable infrastructure
  • Choice of direct-wired or transformer isolated splits
  • Economical Cat 5/6 cable replaces bulky multi-channel audio snake
Analog audio over Cat 5 wiring
The Catapult TX4 and RX4 act like a typical four-channel analog audio snake; they allow you to send mic or line-level signals from one location to another without signal loss, noise, or interference, and without any digital audio conversion needed. What makes the Catapult system unique is that it utilizes Cat 5 Ethernet cable, which is widely available, lightweight, and economical. Simply connect a shielded Cat 5 cable between any two Catapult modules and they will use the analog conductors in the cable to deliver four balanced audio lines to any destination.
Straight-wire passive operation
Catapult modules require no power to operate, and since they keep the signal in the analog realm, no digital conversion is necessary. Straight-wire connection from the XLRs to the RJ45 connector on a Cat 5 cable ensures that your audio passes through without coloration or distortion.
Utilize pre-existing cable installations
As many buildings are already pre-wired for Cat 5, you can take advantage of this to transmit audio between distant rooms without the need to install or supply new cabling. This eliminates the need for bulky and expensive multi-channel audio cable, and allows contractors to benefit from installed network cable and easily connect from one room to another.
Mix & Match to add transformer isolation
All of the Radial Catapult modules are compatible with each other, and each is sold individually, so you can select whichever combination best suits your needs. The Catapult RX4 and TX4 can be used together as a pair, creating a 4-channel audio snake. However, if you need transformer isolation to prevent hum and buzz when splitting audio signals, two additional models of Catapults are available. The TX4L and RX4L have line level isolation transformers for splitting playback tracks or outputs to amp racks, while the TX4M and RX4M can be employed when splitting mic signals on stage. Use any combination of these six models, along with the compact Catapult Mini RX and TX to create a custom snake designed for your unique application.
TX4M R800 8023 00
TX4L R800 8024 00

 

Radial Catapult RX4
R800 8025 00
Radial Catapult 4-Channel Cat 5 Audio Snake Receiver
The Radial Catapult™ is a 4-channel modular audio snake that allows you to send analog audio signals over standard Cat 5 or Cat 6 shielded twisted pair cable.
  • Send four channels of analog audio over a single Cat 5/6 cable
  • Works with a building’s existing cable infrastructure
  • Choice of direct-wired or transformer isolated splits
  • Economical Cat 5/6 cable replaces bulky multi-channel audio snake
Analog audio over Cat 5 wiring
The Catapult TX4 and RX4 act like a typical four-channel analog audio snake; they allow you to send mic or line-level signals from one location to another without signal loss, noise, or interference, and without any digital audio conversion needed. What makes the Catapult system unique is that it utilizes Cat 5 Ethernet cable, which is widely available, lightweight, and economical. Simply connect a shielded Cat 5 cable between any two Catapult modules and they will use the analog conductors in the cable to deliver four balanced audio lines to any destination.
Straight-wire passive operation
Catapult modules require no power to operate, and since they keep the signal in the analog realm, no digital conversion is necessary. Straight-wire connection from the XLRs to the RJ45 connector on a Cat 5 cable ensures that your audio passes through without coloration or distortion.
Utilize pre-existing cable installations
As many buildings are already pre-wired for Cat 5, you can take advantage of this to transmit audio between distant rooms without the need to install or supply new cabling. This eliminates the need for bulky and expensive multi-channel audio cable, and allows contractors to benefit from installed network cable and easily connect from one room to another.
Mix & Match to add transformer isolation
All of the Radial Catapult modules are compatible with each other, and each is sold individually, so you can select whichever combination best suits your needs. The Catapult RX4 and TX4 can be used together as a pair, creating a 4-channel audio snake. However, if you need transformer isolation to prevent hum and buzz when splitting audio signals, two additional models of Catapults are available. The TX4L and RX4L have line level isolation transformers for splitting playback tracks or outputs to amp racks, while the TX4M and RX4M can be employed when splitting mic signals on stage. Use any combination of these six models, along with the compact Catapult Mini RX and TX to create a custom snake designed for your unique application.
RX4M R800 8026 00
RX4L R800 8027 00 
Radial JS2
R800 1022 00
Radial JS2 Passive 2-way Microphone Splitter
The JS2™ is a high performance balanced mic-level splitter designed to send a signal to multiple destinations simultaneously, with one transformer-isolated output and two direct outputs.
  • Send one microphone signal to three destinations simultaneously
  • Jensen transformer-equipped for exceptional audio quality
  • Eliminates hum and buzz caused by ground loops
  • Single isolated output provides optimal noise rejection
Portable mic splitting on stage or in the studio
The JS2 is a professional mic splitter designed to split a single source to multiple destinations simultaneously without signal degradation or noise. A premium Jensen transformer inside provides galvanic isolation to eliminate buzz and hum from ground loops, while maintaining an extremely wide bandwidth with ultra-low distortion and phase shift. Ground lifts on the outputs help further reduce noise, while an input pad allows line-level sources to connected as well. Both the JS2 and the JS3 can be rack mounted for touring and installation purposes, with up to eight fitting in the Radial J-Rak.



Radial JS3
R800 1023 00
Radial JS3 Passive 3-way Microphone Splitter
The JS3™ is a high performance balanced mic-level splitter designed to send a signal to multiple destinations simultaneously, with two transformer-isolated outputs and one direct output.
  • Send one microphone signal to three destinations simultaneously
  • Jensen transformer-equipped for exceptional audio quality
  • Eliminates hum and buzz caused by ground loops
  • Dual isolated outputs provide optimal noise rejection
Portable mic splitting on stage or in the studio
The JS3 is a professional mic splitter designed to split a single source to multiple destinations simultaneously without signal degradation or noise. A premium Jensen transformer inside provides galvanic isolation to eliminate buzz and hum from ground loops, while maintaining an extremely wide bandwidth with ultra-low distortion and phase shift. Ground lifts on the outputs help further reduce noise, while an input pad allows line-level sources to connected as well. Both the JS2 and the JS3 can be rack mounted for touring and installation purposes, with up to eight fitting in the Radial J-Rak.
 
Radial ProMS2
R800 1122 00
Radial ProMS2 Passive 2-way Microphone Splitter
The ProMS2™ is a balanced mic-level splitter designed to send a signal to multiple destinations simultaneously on stage, with one transformer-isolated output and two direct outputs.
  • Send one microphone signal to three destinations simultaneously
  • Eclipse transformer for clean & transparent audio
  • Eliminates hum and buzz caused by ground loops
  • Single isolated output provides optimal noise rejection
Portable mic splitting for stage use
The ProMS2 is a mic splitter designed to split a single source to multiple destinations simultaneously without signal degradation or noise. A high quality Eclipse transformer inside provides galvanic isolation to eliminate hum and buzz from ground loops, while delivering a wide frequency response and low distortion. Ground lifts on the outputs help further reduce noise, while an input pad allows line-level sources to be connected as well. The ProMS2 can be rack mounted for touring and installation purposes, with up to eight fitting in the Radial J-Rak.
Radial LX2 - Line level splitter
R800 1033 00
Radial LX2 Passive Line-Level Splitter & Attenuator
The LX-2™ is a passive balanced line-level audio splitter that allows you to easily send an audio signal to two different destinations at once without noise, while also providing the ability to attenuate the signal when needed.
  • Split one audio signal to two destinations simultaneously
  • Jensen® transformer equipped for exceptional audio quality
  • Eliminates hum and buzz caused by ground loops
  • Variable trim control can be engaged for easy level adjustment
Split & attenuate audio with ease
The LX-2 performs the dual functions of splitting a line level audio signal and providing level attenuation where necessary. A premium Jensen transformer inside provides exceptional frequency response and phase coherency to ensure that the highest audio quality is maintained, while isolating the two outputs from each other to eliminate hum and buzz from ground loops. For situations where a level adjustment is required, the trim control on the LX-2 allows you to attenuate overly hot signals. This gives you the ability to drive your mic preamps hard to achieve coloration, while trimming the level at the LX-2 to avoid clipping the inputs of your recording interface. This trim control is activated by a recessed ‘set & forget’ switch; if attenuation is not needed, simply disengage this switch to prevent accidental and unwanted level adjustments.

 

Radial LX3 - Line level splitter
R800 1034 00
Radial LX-3 Passive Line-Level Splitter
The Radial LX-3™ is a high-performance balanced line-level splitter designed to send one audio signal to as many as three destinations at once.
  • Send one audio signal to three destinations simultaneously
  • Jensen transformer-equipped for exceptional audio quality
  • Eliminates hum and buzz caused by ground loops
  • Combo jack input for 1/4″ TRS or XLR sources
Pristine audio splitting
The LX-3 makes use of a premium Jensen transformer to leverage the industry's best combination of frequency response, signal level handling, and low distortion, providing the highest possible signal quality. It features two isolated outputs to eliminate hum and buzz from ground loops, along with a third direct output. All three XLR outputs have ground lift switches for additional noise suppression, and a switchable -12dB input pad allows you to connect even the hottest line outputs without fear of overloading or distortion. The input of the LX-3 is accessed with an XLR/TRS combo jack, which allows you to connect via balanced or unbalanced cables; the LX-3 will automatically balance the signal at the isolated outputs, preventing interference and signal degradation over long cable runs.
Radial LX8-r - 8 Channel balanced line splitter
R800 8200 00
Radial LX-8 Eight Channel Line-Level Splitter & Isolator
The Radial LX8™ is an eight channel passive line-level splitter designed to send multiple channels to three destinations at once, while providing transformer isolation and eliminating hum and buzz caused by ground loops.
  • 8-Channel balanced line level splitter & isolator
  • Handles +26dB signals without distortion or noise
  • Jensen transformer-equipped for exceptional audio quality
  • Eliminates buzz and hum caused by ground loops
The professional touring signal splitter
The Radial LX8 is designed specifically to manage balanced signal splitting in professional audio systems. The single rack space design begins with a 100% passive circuit which means it does not require any power to operate. Inside, each of the eight channels is equipped with a premium Jensen® JT-123-SLPC transformer that is able to handle transients in excess of +26dB at all frequencies right down to 20Hz without audible distortion. This results in an accurate signal transfer with minimal phase shift or distortion. When used in larger systems, you benefit from significantly lower noise, making the LX8 the best choice for any demanding multi-channel audio system.
Radial Exo-Pod
R800 8012 00
Radial EXO-POD Broadcast Passive Line-Level Splitter
The Exo-Pod™ is a passive broadcast splitter than can take a balanced line output from a mixing console and distribute the signal to up to 14 recording devices. It can also be used in conjunction with the Radial mPress master press box to create a modular solution that provides hundreds of individual press feeds.
  • Passive splitter with 14 transformer-isolated outputs
  • Set & forget trim control to adjust output levels
  • Balanced line-level XLR input can handle up to +24dB
  • Daisy-chain multiple Exo-Pods for large events
Expandable noise-free splitting
The Exo-Pod take a line-level XLR input and splits it cleanly to ten XLR outputs and four 3.5mm TRS jacks for connection to video cameras, hand-held recorders, tablets or other media systems. A variable input trim allows the broadcast technician to reduce the global output level locally for convenience, and all of the outputs are transformer isolated to eliminate hum and buzz that is often encountered due to ground loops. The XLR outputs are supplemented with individual ground lift switches to further abate noise, and an XLR thru connector allows multiple Exo-Pods to be linked together to provide an expandable solution to handle events of any size.



Radial mPress
R800 8010 00
Radial mPress Broadcast Press Box & Signal Splitter
The mPress is a modular & expandable press box that distributes audio to multiple destinations simultaneously, with two on-board microphone preamps and additional controls that eliminate the need for a separate mixer when feeding both a PA and a press gallery.
  • Press box & splitter with expandable outputs
  • Dual mic preamps with on-board limiter
  • Program inputs for background music playback
  • Built-in test tone for easy calibration & troubleshooting
Audio distribution & control for small or large events
The mPress provides full control over any size of press gathering, from community gatherings to international events, and its modular design means it can grow to suit your needs. It features two balanced mic or line inputs with low-noise preamps and high-pass filters, along with a shared limiter to avoid clipping the inputs of any connected recording devices. Separate outputs are provided for a set of powered speakers, with dedicated program inputs that allow you to play background music through the PA when on standby, and a headphone output to silently monitor and cue up playback tracks. The main outputs are controlled separately from the press gallery signals, so you can make adjustments on the fly without affecting previously calibrated recording devices.
Expand output channels with the Exo-Pod
For events where more than eight press outputs are required, the mPress can be used in conjunction with a number of Exo-Pod portable splitters to quickly increase the available channel count. The mPress modular approach replaces the mess of cables that hampers typical press box setups, and instead creates an orderly system that enables you to create zones for various groups within the venue. From each of the mPress XLR outputs as many as four Exo-Pods may be chained together, for a total of 320 microphone or line level outputs and 128 recorder outputs. A built-in 1kHz test tone provides everyone with a reference level and a headphone amplifier on the front of the mPress helps when troubleshooting.

 

 

Radial OX8-j
R800 8004 00
Radial OX8-J 8-channel Microphone Splitter with Jensen Trafo
The OX8™ is an eight channel passive mic splitter designed to send the outputs of multiple microphones to three destinations at once, with transformer isolation and ground lifts to eliminate hum and buzz from ground loops.
  • Balanced 8-channel microphone signal splitter
  • Delivers high quality audio without distortion
  • Choice of Eclipse or premium Jensen transformers
  • Eliminates hum and buzz caused by ground loops
Noise-free microphone splitting
The Radial OX8 is a professional audio tool that is equally at home on a live stage as it is in a broadcast studio, splitting eight microphone signals to multiple destinations simultaneously without noise or distortion, and eliminating hum and buzz from ground loops. Each channel is configured with a balanced input, a direct out which also serves as a return path for 48V phantom power, a thru-put with a ground lift switch, and a fully transformer-isolated output. The OX8 may be ordered with premium Jensen JT-MB-CPC transformers or Eclipse ET-MS10 transformers as an affordable alternative. Each channel also benefits from an ultra-short signal path and built in RF filters to ensure absolute quiet performance even in the most noise-prone environments.

 

 



 

Radial OX8-r
R800 8003 00
Radial OX8-R 8-channel Microphone Splitter with Eclipse Trafo
The OX8™ is an eight channel passive mic splitter designed to send the outputs of multiple microphones to three destinations at once, with transformer isolation and ground lifts to eliminate hum and buzz from ground loops.
  • Balanced 8-channel microphone signal splitter
  • Delivers high quality audio without distortion
  • Choice of Eclipse or premium Jensen transformers
  • Eliminates hum and buzz caused by ground loops
Noise-free microphone splitting
The Radial OX8 is a professional audio tool that is equally at home on a live stage as it is in a broadcast studio, splitting eight microphone signals to multiple destinations simultaneously without noise or distortion, and eliminating hum and buzz from ground loops. Each channel is configured with a balanced input, a direct out which also serves as a return path for 48V phantom power, a thru-put with a ground lift switch, and a fully transformer-isolated output. The OX8 may be ordered with premium Jensen JT-MB-CPC transformers or Eclipse ET-MS10 transformers as an affordable alternative. Each channel also benefits from an ultra-short signal path and built in RF filters to ensure absolute quiet performance even in the most noise-prone environments.
Radial JD7
R800 7000 00
Radial JD7 Studio Guitar Distribution and Splitting
The JD7™ is a guitar signal splitter that is able to drive as many as seven amplifiers at the same time without introducing noise, signal loss, or hum and buzz from ground loops.
  • Drive up to 7 amplifiers and 2 effects loops at the same time
  • Jensen transformer isolation eliminates hum and buzz
  • Built-in Radial Direct box and Reamp capabilities
  • Drag control load correction for natural tone
Natural tone, quiet operation
The JD7 allows you to feed up to seven amplifiers simultaneously, with premium Jensen transformers on the outputs that ensure distortion-free signal transfer while blocking hum and buzz from ground loops. To help retain the natural tone of your instrument, Drag control load correction is also featured on the input so you won't lose the tone and feel of connecting your guitar directly to an amplifier.
Record direct and Reamp through multiple amps
The JD7 has a built-in Radial DI box, so you can take a clean guitar track directly to your recording interface while simultaneously playing through multiple amplifiers. A Reamp input allows you to send your recorded guitar track from your recording device back through any or all of your amps, so you can focus on the performance and have the freedom to tweak your amps and microphones later on.